AirFit™ N30

1. Print the AirFit N30 sizing template in the right dimensions (check the scale).
2. Place the template below your nose, perpendicular to your face. If you have a narrow nose, start with the blue/red side of the template. If you have a wide nose, start with the purple side of the template.
3. Look into a mirror and assess whether your nose falls inside or outside the margins on the template. If you are between two sizes, choose the larger one.
4. If your nose is size S (red) or M (blue), select the appropriate cushion from the AirFit N30 starter pack. If your nose is SW (purple) then you will need to order the N30 small wide cushion as a spare part.

These instructions are for general information purpose only. For full details consult the user guide.

1. Bring the mask towards you so that the left and right indicators are correctly aligned with your nose. Once aligned, hold the cushion under your nose with one hand.
2. Use your other hand to hold the bottom strap of the split band, and pull the headgear over the back of your head.
3. You can adjust the cushion by pulling it away from your nose and settling it back into the correct position.
4. Adjust the split bands to achieve a comfortable fit. To loosen the mask, spread them apart, and to tighten the mask, bring them together.
5. Adjust the length of the headgear through the buckle.
6. Once your mask is secure and comfortable, you can connect the mask tubing and device tubing together and get ready to start therapy.

Remember to make sure that the mask feels comfortable when you’re lying in bed. 

These instructions are for general information purpose only. For full details consult the user guide.

If you feel air escaping from the mask cushion anywhere other than the vent, try the following steps to stop the leak.

1. If the cushion is not sitting correctly, pull it away from your nose and settle it back into position.
2. Adjust the mask tension to achieve a secure seal by tightening or loosening the length of the headgear through the buckle. Adjust only enough for a comfortable seal and do not overtighten.

If you continue to experience mask leak, you should contact your local Resmed representative or clinician. 

These instructions are for general information purpose only. For full details consult the user guide.

1. Make sure you have all the mask components and parts.
2. Locate the small buttonholes at each end of the headgear, and insert each stabiliser into each end.  Remember to keep the grey side of the headband facing outwards at all times.
3. Pull the buttonholes of the headgear over the ends of the stabilisers.
4. Hold the mask frame and stretch the headgear away to check it is securely attached. Ensure the headgear is not twisted.
5. Locate the notch on the cushion and align it with the tab on the top of the frame.
6. Push down on all edges of the cushion to ensure they are securely sealed.

These instructions are for general information purpose only. For full details consult the user guide.

1. Ensure your mask is not connected to your CPAP machine.
2. Hold the cushion securely on one side and pull it away from the frame.
3. Pull the end caps on the headgear until the stabilisers’ slide out of the buttonholes.
4. Slide the headgear off the end of each stabiliser.

These instructions are for general information purpose only. For full details consult the user guide.

Regular inspection of the mask is essential to ensure it is working correctly. If any damage is found, replace the relevant mask component.

1. Examine the AirFit N30 mask system and become familiar with its components.
2. Follow the AirFit N30 user guide instructions to disassemble the mask.
3. Examine the headgear for signs of wear, tear and damage.
4. Examine the frame for signs of wear, tear and damage.
5. Examine the cushion for signs of wear, tear and damage.

These instructions are for general information purpose only. For full details consult the user guide.

1. Follow the AirFit N30 mask disassembly instructions to disconnect the mask cushion.
2. Soak the cushion in warm water and a mild liquid detergent.
3. Hand wash the cushion inside and out with a soft bristle brush.
4. Rinse the cushion under running tap water.
5. Leave the cushion to air dry away from direct sunlight.

These instructions are for general information purpose only. For full details consult the user guide.

1. Follow the AirFit N30 mask disassembly instructions to disconnect the mask headgear and frame.
2. Soak the headgear and frame in warm water and a mild liquid detergent.
3. Hand wash the headgear and frame. Clean the frame by scrubbing it with a soft bristle brush. Please ensure you clean the vent holes thoroughly.
4. Rinse each of the components under running tap water.
5. Shake excess water off the frame and leave each of the cleaned components to air dry away from direct sunlight.

These instructions are for general information purpose only. For full details consult the user guide.